At the MOT, each tyre on the car’s road wheels needs at least 1.6 mm of tread across the central three-quarters of its width, all the way round, and must be free of serious cuts, bulges and exposed cords. Tyres on the same axle must also match in size and construction. A tyre below the tread minimum, or with exposed cords, counts as a Dangerous defect.
How the MOT tyre check works
Tyres are inspected under section 5.2.3 of the DVSA inspection manual in Great Britain. Northern Ireland uses the DVA’s own light vehicle manual, which follows very similar rules with a few differences covered below. The tester looks at four main areas: tread depth, damage, size and construction.
Defects are graded. For tyres, the categories you will see are Major and Dangerous, and which one applies depends on the fault. Our guide to common MOT failure reasons puts tyres in the context of the wider test.
The check applies to the tyres fitted to the car’s road wheels at the time of the test. A spare tyre carried in the boot is not part of the test, but if the tester notices a defect on it, they should tell the person who presented the car.
Tread depth: the 1.6 mm rule
The minimum tread depth is 1.6 mm. The main grooves must meet that depth across the central three-quarters of the tread width and all the way around each tyre. Shallower grooves and sipes are excluded from the measurement.
A tyre below the minimum is a Dangerous defect in both Great Britain and Northern Ireland.
The shoulders are not measured
The tread depth check covers the central band only. The shoulders outside that band can be worn smooth and still meet the tread depth requirement. That does not mean the tyre will pass automatically, because testers also check the whole tyre for damage.
Measure tread in several places around each tyre and across the central band, not just at one point. Uneven wear means one section can drop below 1.6 mm while the rest looks fine. Our pre-MOT checklist covers the other quick checks worth doing at the same time.
Cuts, bulges and other damage
This is where the rules in Great Britain and Northern Ireland differ slightly in wording.
Great Britain
- Exposed ply or cord fails the MOT, regardless of how long the cut is.
- Exposed or damaged cords, tread lifting, and a lump, bulge or tear caused by structural failure are Dangerous defects.
- A cut is a Major defect if it exceeds the greater of 25 mm or 10% of the tyre’s section width and the tester can feel the cords but cannot see them.
Northern Ireland
- A cut that reaches the ply or cords is Dangerous if its length is at least the greater of 25 mm or 10% of the tyre’s section width.
- Any exposed ply or cord, tread lifting, or a lump, bulge or tear caused by structural failure is also Dangerous.
A tyre fouling the car
In both jurisdictions, a tyre that fouls part of the car at the test is a Major defect. Both manuals allow designed contact at the steering lock stops under the conditions they specify.
Tyre sizes
Tyres must match left to right on each axle. Different nominal sizes or different aspect ratios on the same axle are generally a Major defect. The front and rear axles can use different sizes as far as this MOT check is concerned.
Both manuals accept two specific sizing allowances:
- Standard 82% aspect ratio tyres may be paired with 80% tyres.
- If a manufacturer marks a tyre with two sizes, such as 185/75R14 and 185R14, the tester can use either marking.
Space-saver spares in Northern Ireland
Northern Ireland has one extra allowance. The DVA manual says to record an advisory, rather than a failure, when one temporary spare or space-saver is in emergency use and creates an aspect ratio mismatch.
Mixing tyre types
Construction on the same axle
Tyre construction must match on each axle. Mixing radial-ply, cross-ply or bias-belted construction on the same axle is a Major defect. Both manuals treat steel and fabric radial-ply tyres as the same construction, so mixing those two is fine.
Front to rear
For a conventional two-axle car, Great Britain’s road-use rules in regulation 26 of the Road Vehicles (Construction and Use) Regulations 1986 prohibit:
- cross-ply or bias-belted tyres at the rear with radials at the front
- cross-ply tyres at the rear with bias-belted tyres at the front
These rules are subject to the exceptions in regulation 26. In Northern Ireland, the MOT manual lists radial tyres at the front with cross-ply or bias-belted tyres at the rear as a Major defect on four-wheel cars with single wheels.
Run-flat tyres
In Great Britain, the MOT permits run-flat and conventional tyres on the same axle. DVSA advises against that combination, so it is best avoided even though it will not fail the test on that point alone.
MOT tyre rules at a glance
| Check | Great Britain | Northern Ireland |
|---|---|---|
| Tread below 1.6 mm | Dangerous | Dangerous |
| Exposed ply or cord | Dangerous, fails regardless of cut length | Dangerous |
| Cut over 25 mm or 10% of section width | Major if cords can be felt but not seen | Dangerous if it reaches the ply or cords |
| Bulge, lump or tear from structural failure | Dangerous | Dangerous |
| Tyre fouling the car | Major | Major |
| Different sizes on the same axle | Generally Major | Generally Major |
| Mixed construction on the same axle | Major | Major |
| Run-flat mixed with conventional on one axle | Permitted, DVSA advises against | Not covered here |
| Space-saver causing size mismatch | Not covered here | Advisory |
Changes in 2026/27
One tyre-related change took effect in Great Britain on 1 June 2026, but it concerns vans rather than cars. Zero-emission goods vehicles with a design gross weight of 3,501 to 4,250 kg moved to Class 7 MOT testing, and their minimum tread depth rose from 1.0 mm to 1.6 mm. Our guide to the Class 7 van MOT explains that class in more detail.
For passenger cars, no scheduled change to the MOT rules on tread depth, damage, sizes or mixing tyres has been confirmed.
Before your test
Tread depth and visible damage are easy to check at home with a tread gauge and a careful look around each tyre. It is also worth checking pressures, as covered in our guide to tyre pressure and TPMS. If your test is coming up, the MOT due date calculator shows when it is due.
Frequently asked questions
What is the legal minimum tyre tread depth for an MOT?
The main grooves must be at least 1.6 mm deep across the central three-quarters of the tread width and all the way around each tyre. A tyre below the minimum is a Dangerous defect in both Great Britain and Northern Ireland.
Will a cut in my tyre fail the MOT?
Exposed ply or cord fails the MOT in Great Britain regardless of cut length. A cut is a Major defect if it exceeds the greater of 25 mm or 10% of the tyre's section width and the tester can feel the cords but cannot see them.
Can I have different size tyres on my car for the MOT?
Tyres must match in nominal size and aspect ratio left to right on each axle, otherwise it is generally a Major defect. The front and rear axles can use different sizes under the MOT check.
Can I mix run-flat and normal tyres for the MOT?
In Great Britain, run-flat and conventional tyres on the same axle are permitted at the MOT, although DVSA advises against that combination. Mixing radial-ply, cross-ply or bias-belted construction on the same axle is a Major defect.
Is the spare tyre checked at the MOT?
No. The tyre check applies to tyres fitted to the road wheels at the time of the test. If the tester notices a defect on a spare carried in the car, they should tell the person who presented it.
Sources
- DVSA: MOT inspection manual, section 5.2.3 tyres
- DVA: Light vehicle inspection manual, tyres
- Road Vehicles (Construction and Use) Regulations 1986
- DVSA: MOT special notice 01-26, zero-emission goods vehicles becoming Class 7
- DVSA: MOT inspection manual updates
PlateScout is independent and not affiliated with the DVLA, DVSA, TfL or any government body. Rules and rates change: always check the official source before you act.
Check a number plate now
See when and where a car was first registered, free and without signing up.