Brake pads should be replaced when about 3 mm of friction material is left, which is the point the RAC recommends, or sooner if a wear warning appears or you hear grinding. Brake discs need replacing when they wear below the manufacturer’s minimum thickness, or earlier if they are cracked, deeply scored or distorted. Pads are replaced in axle sets, and new discs always go on in axle pairs with new pads.
How long do brake pads last?
There is no single mileage at which brake pads wear out. Pad life varies with the car and how it is driven, so the RAC advises using the measured thickness and condition of the pads to decide when to replace them. Two identical cars can need new pads at very different points depending on how and where they are used.
That makes regular checks more useful than a fixed schedule. A garage can measure the remaining friction material during a service or inspection, and you can ask them to note the reading so you know roughly how much life is left.
When to replace brake pads
The 3 mm guide
The RAC recommends replacing pads when 3 mm of friction material remains. This is a practical replacement point that leaves a margin before the pad reaches the much lower thicknesses treated as defects at the MOT.
Wear indicators
Many pads have a built-in way of telling you they are worn:
- Metal wear indicator. Some pads have a small metal tab that squeals when it contacts the disc.
- Groove. Other pads have a groove in the friction material that disappears when the pad needs replacing.
- Pad wear warning light. Some cars have an electronic sensor that switches on a light on the dashboard. Check the vehicle handbook for what the warning means on your car, and see our dashboard warning lights guide for the common symbols.
Warning signs you should not ignore
| What you notice | What it can mean | What to do |
|---|---|---|
| Pad wear warning light | Pads may need replacing | Get the brakes checked promptly |
| Persistent squealing under braking | A metal wear indicator may be touching the disc | Get the brakes checked promptly |
| Grinding under braking | The pad friction material may have worn away | Stop driving as soon as it is safe and arrange an inspection |
| Vibration under braking | A brake problem that needs looking at | Arrange a prompt inspection |
| Weaker braking | A brake problem that needs looking at | Arrange a prompt inspection |
Grinding is the most urgent of these. It can mean there is little or nothing left of the pad, so do not keep driving and hope it goes away.
When to replace brake discs
Minimum thickness
Every disc has a minimum thickness set by the manufacturer, and that limit is specific to the disc fitted to your car. Look for a MIN TH marking on the disc itself. A technician measures the friction surface at several points and compares the lowest reading with the specified limit. A disc below that limit needs replacing.
Damage
Discs do not only wear out. Damage can mean a disc needs replacing before it reaches its thickness limit. Brembo lists these as reasons to replace a disc:
- radial cracks
- deep circular scoring
- significant distortion of the braking surface
Replacing pads and discs together
A few simple rules apply whenever brakes are replaced:
- Replace pads in axle sets, so both wheels on the same axle get new pads at the same time.
- Replace discs in axle pairs.
- Fit new pads whenever new discs are fitted.
- If only the pads are worn, the discs should be checked for damage and measured against the manufacturer’s specification before deciding whether they can stay in service.
This means a pad change does not automatically mean new discs, but it should always include a proper look at the discs.
When a garage quotes for new pads, ask whether the discs were measured and what the reading was compared with the minimum thickness. That tells you whether the discs can stay or are close to needing replacement at the next visit.
Brake pads, discs and the MOT
The MOT treats worn brakes in terms of defect categories. In Great Britain, both Major and Dangerous defects fail the test. For more on how the brakes are tested, see our MOT brake test explained.
| Component | Major defect (fail) | Dangerous defect (fail) |
|---|---|---|
| Brake pads (GB) | Worn down to the wear indicator | Worn below 1.5 mm |
| Brake discs (GB) | Significant and obvious wear | Insecure, fractured or otherwise likely to fail |
Two details are worth knowing:
- An illuminated pad wear warning light on its own does not cause an MOT failure.
- A disc measuring below the manufacturer’s recommended limit does not by itself trigger an MOT failure.
Northern Ireland
In Northern Ireland, the DVA classes a pad below 1.5 mm at any point, or an insecure pad, as Dangerous. Its manual classes a cracked disc, or one with excessive scoring, pitting or wear, as Major.
Why passing the MOT is not the same as good brakes
The MOT thresholds and the replacement guides are not the same thing. A pad only becomes a Dangerous defect below 1.5 mm, well under the 3 mm the RAC recommends as a replacement point. A disc below its minimum thickness can also pass on that measurement alone.
The Great Britain MOT is also carried out without dismantling, which can limit what the tester sees. So act on warning signs between tests rather than waiting for the next MOT. The Highway Code advises stopping to investigate if a warning light comes on while you are driving. Brakes also feature among the common reasons for MOT failure, and you can check when your next test is due with our MOT due date calculator.
Are the rules changing?
No forthcoming change to the MOT wear criteria for car pads or discs has been announced by the DVSA or the DVA.
Separately, the Department for Transport plans to require Euro 7 for new unlimited-series light-duty vehicle registrations in Great Britain from 29 November 2027. Euro 7 includes new brake wear emissions requirements, but the department intends to exempt replacement brakes fitted to Euro 7 vehicles from those requirements initially. The date they will apply to replacement brakes has not been confirmed. For more on keeping your car in good shape, browse our car maintenance guide.
Frequently asked questions
At what thickness should brake pads be replaced?
The RAC recommends replacing brake pads when 3 mm of friction material remains. Pad life varies with the car and how it is driven, so use the measured thickness and condition rather than mileage alone.
How do I know if my brake discs need replacing?
A disc needs replacing when it is below the manufacturer's minimum thickness, often marked MIN TH on the disc. Radial cracks, deep circular scoring or significant distortion of the braking surface can also mean a disc needs replacing before it reaches that limit.
Will worn brake pads fail the MOT?
In Great Britain, a pad worn down to its wear indicator is a Major defect, and a pad worn below 1.5 mm is a Dangerous defect. Both fail the test. An illuminated pad wear warning light on its own does not cause an MOT failure.
Should brake pads be changed when discs are replaced?
Yes. Fit new pads when fitting new discs, and replace pads in axle sets and discs in axle pairs. If only the pads are worn, the discs should be checked for damage and measured against the manufacturer's specification.
What does grinding from the brakes mean?
Grinding under braking can indicate that the pad friction material has worn away. The RAC advises stopping as soon as it is safe and arranging an inspection.
Sources
- RAC, brake pads advice
- DVSA, MOT inspection manual: brakes
- DVSA, MOT inspection manual: introduction
- Valeo Service UK, technical bulletin BR-006
- Brembo, disc indications and bedding in
- DVA, mechanical brake components
- Highway Code, annex 6: vehicle maintenance
- Department for Transport, minimum emission standard for new road vehicles
PlateScout is independent and not affiliated with the DVLA, DVSA, TfL or any government body. Rules and rates change: always check the official source before you act.
Check a number plate now
See when and where a car was first registered, free and without signing up.